8% di sconto

KTM FLASH KTMFLASH Auto ECU Programmatore Supporta V-A-G DQ200 DQ250 Infineon Bosch Supporta 271 MSV80 MSV90 con Cavo Dialink J2534 Software V1.94

Serie No.SE140 Esaurito. Storia 49 vendite.

Ultimo prezzo: 249.00
Prezzo al dettaglio: 228.00 8% off
Ciao tutti:

3.28 Grande Promo,solo 10 giorni, Clica qui!
I prodotti più venduti ai prezzi più bassi!

2024 Fortissimo Full Versione FoxFlash ECU TCU Programmatore clica qui
Ora acquista foxflash 328 Promo Prezzo con €603 ottenere 3 Regali gratis !


Contattarci:
Whatsapp: +8618580434781
Peso:
0.5KG
Pacchetto:
28.5cm*18cm*7cm ( Inch: 11.22*7.09*2.76 )
Ritorno:
Rimborso entro 7 giorni, il compratore paga il trasporto di ritorno. I dettagli»

Descrizione del prodotto

KTM FlASH ECU Programmatore supporta la trasmissione VAG DQ200 DQ 250 DQ500 VL381 DL501, legge eeprom auto cinese via OBD, leggi Infineon tramite la modalità di avvio, supporta la lettura e la scrittura di dati auto cinese ME17 TC1728 / 1767 e la lettura della password. Sarà disponibile nel mese di giugno 2018
KTM FLASH KTMFLASH Auto ECU Programmatore Supporta V-A-G DQ200 DQ250 Infineon Bosch


KTMflash ECU Programmer Functions:

1. Read the Chinese car via OBD.
2. Read the BOOT mode according to the chip model
3. Read the encrypted ECU password (Read the password of encrypted ECU first, then read data)
4. Support cars made in China with ME17 TC1728/1767 for data reading & writting and password reading.
 
KTMOBD KTMflash software display:

KTMOBD KTMflash software display-01

KTMOBD KTMflash software display-02

KTMOBD KTMflash software display-03

KTMOBD KTMflash software display-04

KTMOBD KTMflash software display-05


KTMflash Workable Transmission Model

V-A-G: DQ200 (0AM)
V-A-G: DQ200MQB/ G2 (0CW)
V-A-G: DQ250C (02E) K-Line
V-A-G: DQ250E/ F (02E)
V-A-G: DQ250MQB (0D9)
V-A-G: VL300/ V30 (01J/ 0AN) K-Line
V-A-G: VL300/ V30 (01J/ 0AN)
V-A-G: VL381 (0AW)
V-A-G: DQ500 (0BH/ 0BT)
V-A-G: DL501/ G2 (0B5)
V-A-G: DQ200/ MQB Boot (MICRO)
V-A-G: DQ200/ MQB Boot (EEPROM)
V-A-G: DQ200G2 Boot (MICRO)
V-A-G: DQ200G2 Boot (EEPROM)
V-A-G: DQ250E/ F/ MQB Boot (MICRO)
V-A-G: DQ250E/ F/ MQB Boot (EEPROM)
V-A-G: VL300/ V30 BSL (FLASH)
V-A-G: VL300/ V30 BSL (EEPROM)
V-A-G: VL381 Boot (MICRO)
V-A-G: VL381 Boot (EEPROM)
V-A-G: DL501 Boot (MICRO)
V-A-G: DL501 Boot (EEPROM)
V-A-G: DL501G2 Boot (MICRO)
V-A-G: DL501G2 Boot (EEPROM)

Read Chinese car via OBD
China: Chery, Great Wall, Lifan, SAIC ME17 (ME17.8.8)
China: Chery, Great Wall, Lifan MT80 K-Line Calibration (Delphi MT80)
China: Chery, Great Wall, Lifan MT80 CAN-bus (Delphi MT80)

Read the BOOT mode according to the chip model
Infineon: TC1762/ TC1766 MICRO (1504KB)
Infineon: TC1762/ TC1766 EEPROM (32KB)
Infineon: TC1792/ TC1796 MICRO (2048KB)
Infineon: TC1796 MICRO+EXT (4096KB/ 6144KB)
Infineon: TC1796 EXT (2048KB/ 4096KB)
Infineon: TC1796 EEPROM (128KB)
Infineon: TC1792 EEPROM (64KB)
Infineon: TC1738/ TC1767 MICRO (2048KB)
Infineon: TC1738/ TC1767 EEPROM (64KB)
Infineon: TC1797 MICRO (4096KB)
Infineon: TC1797 MICRO+EXT (6144KB/ 8192KB)
Infineon: TC1797 EXT (2048KB/ 4096KB)
Infineon: TC1797 EEPROM (64KB)
Infineon: TC1724/ TC1728 MICRO (1536KB)
Infineon: TC1724/ TC1728 EEPROM (64KB)
Infineon: TC1782/ TC1784 MICRO (2560KB)
Infineon: TC1782/ TC1784 EEPROM (128KB)
Infineon: TC1793/ TC1798 MICRO (4096KB)
Infineon: TC1793/ TC1798 MICRO+EXT (6144KB/ 8192KB)
Infineon: TC1793/ TC1798 EXT (2048KB/ 4096KB)
Infineon: TC1793/ TC1798 EEPROM (192KB)

Bosch: Support Chinese car ME17 TC1728/1767 data reading & writing and password reading
Bosch: BMW/ MB/ V-A-G GPT
Bosch: Ford/ Opel/ Volvo GPT
Bosch: BMW TPROT8+
Bosch: V-A-G TPROT8+
Bosch: Kia/ Hyundai/ Honda TPROT8+
Bosch: Chrysler/ Jeep/ Dodge/ Fiat TPROT8+ [Test]
Bosch: VAZ/ UAZ ME17.9.71  
Continental: Kia/ Hyundai/ SsangYong SIM2K-24X/ C201
Continental: Ford EMS2204
Continental: Ford EMS2207
Continental: Ford EMS2211
Continental: Ford SID208
Continental: Ford SID209
Continental: Ford Mondeo 4 SID807EVO
Continental: Ford Focus 3/ Transit Connect SID807EVO
Continental: Citroen/ Peugeot SID208
Kia/ Hyundai: Delphi MT86 EEPROM (16KB)
Mercedes-Benz: Delphi CRD3.1 EEPROM (32KB)


How to use KTM FlASH switchboard?

1. The switchboard is designed to work with J2534, this device uses the Ktag cables so the user can refer to the Ktag wiring diagram.
2. Advise you use Open Port2.0 as the protocol conversion equipment and work with PC.
3. There are 3 types of Bosch Infineon ECU :
1) The Infineon ECU before TPROT8.
2) TPROT8-10
3) The Infineon ECU after TPROT10 which is what we call GPT encrypted.
4. The Infineon ECU before TPROT8 is not encrypted, you directly uses the BOOT point
grounding, then follow the Ktag user manual to wire the cable and read the data.
 
5. For TPROT8-10, the Bosch Company set the anti-debugging mode, reading EEPROM needs no password and reading Flash needs a password.
Therefore, during the reading process, there is an extra CNF1, Boot outputs low level and CNF1 outputs high level. When reading, Boot needs to add one small resistor and ground it. CNF1 to connect one 470ohm-2K resistance, then connect 3.3V, it's very important, otherwise, the ECU will be burnout.

2 tips on reading the data:
1) BOOT and CNF1 must be connected when reading data.
2) Only connect BOOT, not CNF1 When reading the password, otherwise, the password can't be read out. Also, you can follow the Ktag wiring diagram because Ktag controls the CNF1 turn on and off, so it can't be disconnected. When reading the password, you turn the two switches to the automatic mode, and to the On mode when reading the data, when the software prompts, you choose " Manually" then follow the message to turn on or off.
 
6. For GPT encrypted ECU, the S1, S2, and Boot cable are needed to connected when reading password, and the S1, S2 don't need to be connected when reading data.


KTM bench vs KTMOBD vs KTM Flash:
 
ECU Programmatore KTM bench KTMOBD KTM FLASH
Immagine
linguaggio Inglese, russo Inglese, russo Inglese, russo
Software Sarà rilasciato KTMflash KTMflash
Aggiornamento Sarà rilasciato È necessario aggiornare sia il dongle che il software È necessario aggiornare sia il dongle che il software
Sistema operativo Window XP; Windows 7; Windows 10; Window XP; Windows 7; Windows 10; Window XP; Windows 7; Windows 10;
Velocità Alto Alto Alto
Rischio Meno rischi Meno rischi Rischioso
Metodo via Boot sulla Bench (Non c'è bisogno di aprire il coperchio) via OBD La maggior parte delle centraline elettroniche deve essere smontata per r / w
ECU smontare NO NO Più sì!
ECU leggere /scrivere sì sì sì
Cambio o trasmissione lettura / scrittura NO Sì, solo alcuni sì
Chip di lettura / scrittura NO sì sì


KTMflash Package includes:

1pc x KTMflash ECU Programmer
1pc x KTMflash USB Dongle
 

Marchio Caldo Prodotti:




2024 Nuovo Alientech Originale KESS V3 Guarda Qui :


Modalità di spedizione e tempi di consegna:

EU(Ceca) Spedizione: 3-5 giorni lavorativi:
  Abbiamo immagazzinato articoli di vendita caldi in EU (Ceca) e Amazon EU(Ceca) Warehouse, che è più conveniente per te. TASSE gratuita, spedizione più veloce con un prezzo più economico.
Spedizione DHL: 3-4 giorni lavorativi, per aiutarti nella liquidazione, ti aiuteremo a dichiarare un prezzo più basso sulla liquidazione della fattura. Se l'indirizzo è remoto, il cliente ha bisogno di pagare il trasporto remoto o spediremo tramite posta normale o Yanwen Express.Ma ora spediamo con DHL ce dogana da pagare,qundi se non vuoi pagare dogana spese spediamo con YANWEN EXPRESS.
Yanwen Express: 5-10 giorni lavorativi, di solito nessuna tassa per i paesi europei o l'area remota. La tassa era pre-pagata, quando il pacchetto è stato raggiunto, non c'è nessuna tassa per i clienti.

AutoOBD2.it Passo di Spedizione:
 

Qualsiasi domanda, non esitate a contattarci:

Whatsapp: +86 18580434781
Skype: AutoOBD.it
Email: Sales@AutoOBD2.it
Live-Chat: Chatta con noi Online
Compra di più e risparmia di più